Exam60

California B2 Roof-Ceiling Construction Practice Quiz Overview

Are you ready to test your roof-ceiling expertise? This focused quiz helps you master the structural concepts essential for your California B2 Residential Remodeling exam success.

Exam Details

Time Limit
30 minutes

Questions
15 randomly selected

Question Bank
40 unique questions

Test-Taking Tips

Use your time wisely - Just 2 minutes per question

Not sure about an answer? Use the bookmark feature to flag questions for review

Cost per attempt: 10 Free Attempts

Format: Open-book, but the actual exam is closed.

Take a deep breath, get comfortable, and click "Start" when you're ready to begin. Good luck!

Study Smart!

Each fresh attempt gives you:

New question combinations

Practice managing your time (2 minutes per question)

The number of attempts remaining is 10

Please enter your following information to get started:

1 / 15

In cold-formed steel roof framing, roof sheathing must be fastened to rafters using No. 8 screws spaced _____ at interior supports.

A) 6 inches

B) 8 inches

C) 10 inches

D) 12 inches

2 / 15

In wood roof framing, holes bored or cut into members must not be closer than__________ to the top or bottom of the member, or to any other hole located in the member.

A) 1 inch

B) 2 inches

C) 3 inches

D) 4 inches

3 / 15

In cold-formed steel roof framing, screws for attaching structural sheathing to cold-formed steel roof framing must be installed with a minimum edge distance of__________

A) 1/8 inch

B) 1/4 inch

C) 3/8 inch

D) 7/8 inch

4 / 15

In wood framed roof systems, an opening can be framed using a single header and single trimmer joists if the header joist span does not exceed__________ and is located within 3 feet of the trimmer joist bearing.

A) 3 feet

B) 4 feet

C) 5 feet

D) 6 feet

5 / 15

In cold-formed steel roof framing, web holes in roof framing members must have a min. distance between the edge of the bearing surface and the edge of the web hole of__________.

A) 5 inches

B) 10 inches

C) 15 inches

D) 20 inches

6 / 15

True or False: Spaced lumber sheathing is not allowed in Seismic Design Category D2.

Untitled 59

A) True

B) False

7 / 15

In wood framed roof system openings, tail joists over__________ long must be supported at the header by framing anchors or on ledger strips.

A) 8 feet

B) 10 feet

C) 12 feet

D) 14 feet

8 / 15

Where 3/8-inch wood structural panels having a span rating of 16/0 are used as roof sheathing, what is the maximum span with edge support?

A) 16 inches

B) 20 inches

C) 24 inches

D) 30 inches

9 / 15

In wood roof framing, diameter of holes bored or cut into members must not exceed__________ the depth of the member.

A) 1/4

B) 1/3

C) 1/2

D) 3/4

10 / 15

In wood roof framing, notches in sawn lumber joists, rafters and beams must not__________.

A) exceed 1/6 of the depth of the member

B) be longer than 1/3 of the depth of the member

C) be located in the middle one-third of the span

D) All of the above

11 / 15

Cold-formed steel roof framing must be located in line with load-bearing studs with a max. tolerance of __________ between the centerline of the horizontal framing member and the centerline of the vertical framing member.

A) 1/4 inch

B) 1/2 inch

C) 3/4 inch

D) 1 inch

12 / 15

What is the maximum roof rafter span of a member designation of 800S162-68, where the ground snow load is 30 psf and the rafter spacing is 16 inches o.c.?

A) 22 feet, 2 inches

B) 24 feet, 7 inches

C) 26 feet, 6 inches

D) 27 feet, 1 inches

13 / 15

Wood structural panel used as roof sheathing in wood roof framing must be installed with joints _____.

A) staggered

B) not staggered

C) Either A or B

D) Neither A nor B

14 / 15

In cold-formed steel roof framing, web holes in roof framing members must have a center-to-center spacing of__________ min.

A) 12 inches

B) 24 inches

C) 36 inches

D) 48 inches

15 / 15

In cold-formed steel roof framing, ceiling joists must be connected to roof rafters (heel joint) with _____.

A) No. 6 screws

B) No. 8 screws

C) No. 10 screws

D) No. 12 screws

Your score is

The average score is 0%

0%

Report a question

California B2 Roof-Ceiling Construction Practice Quiz Overview

Exam Details

Test-Taking Tips